Panel Mount Connectors

Results:

Panel mount connectors create fixed signal or power interfaces on equipment panels, enclosures and external cases. Because this product range also includes selected free-hanging and wire-mount parts, first confirm the listed mounting type. For a true panel-mounted design, compare the cutout, panel thickness, retention method, termination and mating components.

Confirm What Is Actually Mounted

Mounting type describes where the connector is mechanically secured. Use the product attributes and manufacturer drawing to distinguish the available arrangements before comparing electrical ratings.

Arrangement How to identify it Primary design input
Panel mount Secured to a panel or enclosure through a specified cutout Cutout, panel thickness and retention hardware
Free hanging or in-line Remains on the cable instead of being fixed to a panel Cable exit, strain relief and mating retention
Board mount Mechanically secured or soldered to a PCB PCB footprint, orientation and solder termination
Panel and board mount Interfaces with both an enclosure and a PCB Alignment among the panel, connector and PCB

If the required interface is not panel-mounted, compare the wider Rectangular Connectors range. The PCB Connector Selection Guide also explains how a mounting flange and a board lock perform different mechanical roles.

Translate the Enclosure Drawing into Requirements

Begin with the mechanical boundary rather than connector appearance. Record the required panel cutout dimensions, panel thickness and the permitted connector projection on both sides of the enclosure.

  • Mounting position: Determine whether the connector is installed from the front, rear or side of the panel.
  • Panel retention: Match the design to snap-in tabs, mounting flanges, screws, nuts or the specified hardware.
  • Internal clearance: Allow space for contacts, cable routing, a backshell or a PCB behind the panel.
  • External clearance: Reserve enough room to mate, lock and remove the external connector.
  • Cable direction: Check whether a straight or right-angle exit fits the enclosure and minimum cable bend radius.

Define Both Sides of the Panel Interface

Panel side Questions to resolve
Outside the enclosure What cable or equipment will mate, and which plug or receptacle and locking method does it require?
Inside the enclosure Will the connection use crimp wire, IDC, solder terminals or a PCB, and how much routing space is available?

Then match connector type, positions, pitch, row count, contact gender and supported wire size. For products supplied without conductive terminals, select series-compatible parts from Rectangular Connector Contacts. If the insulating shell is ordered separately, compare compatible options under Rectangular Connector Housings.

Separate Panel Retention from Mating Retention

Panel retention keeps the fixed connector attached to the enclosure. Mating retention keeps the two connector halves engaged. Check both independently: a snap-in housing may secure the panel side while a latch, locking ramp, screw coupling or push-pull mechanism retains the mating connector.

Panel mounting alone does not establish a waterproof interface. Use an IP or sealing rating only when the manufacturer specifies it for the complete mated system, including the required gasket, seals, backshell and cable arrangement.

Complete the Mating and Installation Record

  1. Record the manufacturer series and exact panel-mounted part number.
  2. Confirm the specified mating plug or receptacle, polarization and keying.
  3. List separately ordered contacts, seals, backshells, strain relief and mounting hardware.
  4. Verify the termination tooling and assembly sequence.
  5. Retain the manufacturer drawing with the approved panel cutout and installation dimensions.

Finally, check current and voltage ratings, contact resistance, operating temperature, mating cycles, vibration and shielding requirements for the exact configuration. Matching pitch and position count alone does not establish compatibility; confirm the complete mating pair in the manufacturer documentation.

Read More
Panel Mount ConnectorsResults:
Comprehensive
Price Priority
Stock Priority
Image
Part Number
Description
Availability
Unit Price(USD)
Quantity
Operation
ARATAS
ECAD Model:
Available Stock
8
Estimated Ship Time:6-13 working days
1+$5.0025
10+$4.136
1,040+$2.916
2,560+$2.7324
- +
Ext. Price(USD):$15.00
MOQ:3
Mult:1
SPQ:1
25 / PageGoto