Modular Jacks

Results:

Modular jacks are board-mounted receptacles used to connect telephone, data and Ethernet cables to electronic equipment. This category includes PCB-mount modular jacks in RJ45 8P8C and RJ11, RJ12 and RJ25 configurations, with single-port, multi-port, vertical, right-angle, shielded and LED-equipped options.

Start by matching the contact configuration and mating plug, then verify the PCB footprint, port orientation and enclosure opening. For Ethernet designs requiring integrated isolation magnetics, compare products in the Magnetic Jack Connectors category.

Decode the Modular Jack from the PCB Side

A modular jack must match both the cable interface and the physical board layout. Review the connector from four directions before comparing individual part numbers.

INTERFACE FACE

Contact Configuration

Confirm the required positions and loaded contacts, such as 4P4C, 6P4C, 6P6C or 8P8C. A similar housing shape does not guarantee electrical compatibility.

BOARD SIDE

PCB Footprint

Match the signal-pin pattern, shield tabs, locating posts and board-retention features. Check whether the jack uses through-hole, surface-mount or mixed mounting.

CABLE SIDE

Port Orientation

Select vertical or right-angle entry and confirm whether the plug latch faces up or down. Port direction affects cable routing and enclosure clearance.

PANEL SIDE

Enclosure Integration

Verify the panel opening, connector height, board-edge distance and plug-release clearance, especially for multi-port and stacked assemblies.

Match the Port Layout to the Equipment

Port count and arrangement influence PCB area, panel geometry, shielding and service access. Use the equipment layout to narrow the available jack configurations.

Port Layout Typical Equipment Mechanical Checks
Single Port Compact controllers, instruments and embedded devices Orientation, latch direction, PCB edge distance and enclosure clearance
Ganged Multi-Port Routers, switches and communication equipment Port count, center-to-center spacing, shared shield and LED arrangement
Stacked Ports High-density front panels and network appliances Overall height, panel cutout, airflow, board retention and service access

Confirm the Interface and Network Requirement

For Ethernet designs, compare RJ45 8P8C modular jacks by supported network category, shielding, port count and LED configuration. For telephone and control interfaces, verify the exact contact loading of RJ11, RJ12 or RJ25 formats instead of selecting by the shared housing shape.

Also confirm that the mating modular plug uses the same contact configuration and compatible latch geometry.

Standard Modular Jack or Magnetic Jack?

The two connector types can share a similar RJ45 interface but perform different electrical functions. Identify whether the Ethernet isolation components are located elsewhere on the PCB or must be integrated into the connector.

Standard Modular Jack

Provides the mechanical port and electrical contacts. Use this type when transformers, common-mode chokes or other isolation components are implemented separately on the PCB.

Magnetic Jack

Integrates Ethernet magnetics into the connector housing. Match the magnetic circuit, speed, pinout, PoE requirement and PHY reference design.

Browse Magnetic Jack Connectors.

Record the PCB and Panel Requirements

Before selecting a part number, record the mechanical and electrical details needed to place the jack on the board and expose the port through the enclosure.

Interface: RJ type, positions and loaded contacts
Mounting: Through-hole, SMT or mixed mounting
Footprint: Pin spacing, shield tabs and post locations
Orientation: Vertical, right-angle, latch up or latch down
Port Layout: Single, ganged or stacked
Features: Shielding, LEDs and board retention
Panel: Opening size, board-edge position and clearance
Mating Part: Compatible modular plug and cable system
Read More
Modular JacksResults:
Comprehensive
Price Priority
Stock Priority
Image
Part Number
Description
Availability
Unit Price(USD)
Quantity
Operation
Jack Up,straight line 8p8c (RJ45, Ethernet) 1 SMD mount
Available Stock
44
Estimated Ship Time:9-14 working days
1+$4.55
- +
Ext. Price(USD):$27.30
MOQ:6
Mult:1
SPQ:1
Jack Up,straight line 8p8c (RJ45, Ethernet) 1 SMD mount
Available Stock
83
Estimated Ship Time:9-14 working days
1+$5.096
- +
Ext. Price(USD):$30.57
MOQ:6
Mult:1
SPQ:1
25 / PageGoto