Male Pin Headers

Results:

Male pin headers provide exposed male contacts for connecting a PCB to a female socket, cable connector or another board. Select a compatible part by matching pitch, positions, rows, orientation and mounting method first, then verify mating-post length, PCB termination, plating, current rating and mechanical retention.

Start with the PCB Interface

Begin with the PCB layout rather than the connector appearance. Confirm the contact pitch, total number of positions, number of rows and row spacing. The footprint must also support the required through-hole or surface-mount termination and provide sufficient clearance for the connector body and its mating component.

Selection Parameter What to Check Why It Matters
Pitch Center-to-center contact spacing Controls PCB footprint and mating compatibility
Positions and Rows Total contacts, single or dual row, and loaded positions Determines circuit count and connector size
Orientation Vertical or right-angle mating direction Affects enclosure access and board-edge placement
Mounting Method Through-hole or surface-mount termination Defines the PCB layout and assembly process

Build the Required Header Geometry

After defining the footprint, compare the dimensions above and below the insulator. The mating-post length must provide sufficient engagement with the female contact without bottoming out. The PCB-tail length must suit the board thickness, hole design or SMT pad pattern. Insulator height and overall contact length determine the available clearance around the connection.

  • Mating-post length: the exposed male contact available for insertion.
  • PCB-tail length: the portion soldered or terminated to the board.
  • Insulator height: the plastic body height above the PCB.
  • Pin cross-section: the contact width and thickness accepted by the mating socket.
  • Overall length: the complete contact dimension used when comparing alternatives.

Choose Orientation and Mounting

Vertical headers support perpendicular mating above the PCB, while right-angle headers route the connection toward the board edge. Through-hole products provide strong mechanical retention and require compatible finished-hole dimensions. Surface-mount headers reduce the need for plated holes but require a suitable land pattern, adequate coplanarity and stable placement during reflow.

Shrouded, keyed or locking headers can add polarization and retention when the application must reduce misalignment or accidental disconnection. Confirm these mechanical features against the complete connector series rather than relying only on pitch and pin count.

Match the Female Connector

A compatible female connector must match the pitch, positions, rows and contact arrangement of the male header. Also verify the accepted pin cross-section, minimum and maximum mating depth, polarization, keying and contact plating. Browse Female Socket Headers when selecting the corresponding receptacle or socket side.

Check Electrical and Mechanical Requirements

Compare current and voltage ratings, contact resistance, insulation resistance, operating temperature and contact plating. Gold-plated mating surfaces may suit frequent mating or low-level signals, while tin-plated contacts are commonly used for cost-sensitive applications with fewer mating cycles. Environmental conditions, vibration and required retention should also be considered.

For a complete review of pitch, mounting, pin dimensions, datasheets and alternative-part evaluation, refer to the PCB Pin Header Selection Guide.

Choose the Correct Header Category

  • Use male pin headers for conventional exposed male contacts mounted on a PCB.
  • Browse Special Pin Headers when the design requires unusual pin lengths, custom row arrangements or non-standard geometry.
  • Consider Board Stacking Connectors for elevated boards, pass-through contacts or controlled board-to-board spacing.

Prepare a Replacement Checklist

Before approving an alternative, record the pitch, positions, rows, row spacing, orientation, mounting method, mating-post length, PCB-tail length, insulator height, pin cross-section, plating, electrical ratings and mating connector. Confirm the manufacturer drawing and recommended PCB footprint because parts with similar descriptions may have different mechanical dimensions.

Read More
Male Pin HeadersResults:
Comprehensive
Price Priority
Stock Priority
Image
Part Number
Description
Availability
Unit Price(USD)
Quantity
Operation
Pin Header 2x7P 2.54mm 11.2mm ROHS
Available Stock
2,500
Estimated Ship Time:7-12 working days
25+
1,000+$0.0287
2,000+$0.0281
3,000+$0.0275
4,000+$0.0268
- +
Ext. Price(USD):$28.70
MOQ:1,000
Mult:500
SPQ:500
Pin Header 2x6P 2.54mm 11.2mm ROHS
Available Stock
2,500
Estimated Ship Time:7-12 working days
25+
1,000+$0.0239
2,000+$0.0235
3,000+$0.0228
4,000+$0.0223
- +
Ext. Price(USD):$23.90
MOQ:1,000
Mult:500
SPQ:500
25 / PageGoto