Custom Backplane Connectors

Results:

Custom backplane connectors in this category are specialized, series-dependent interconnect products for a defined board system or equipment architecture. Determine first whether the connector belongs to an established standard category; if not, identify it through the manufacturer, product family and complete mating system.

Decide Whether the Connector Belongs Here

  • Does the equipment specify an ARINC interface?
    Use ARINC Connectors for the corresponding rack-and-panel connector family.
  • Does it use a standardized hard metric architecture?
  • Does the drawing identify a DIN connector form?
    Match the specified interface under DIN 41612 Connectors.
  • If none of these standards defines the mating system
    Continue in this category and identify the specialized connector from its manufacturer series, board function and mating components.
“Custom” describes a specialized or series-specific connector interface. It does not mean that every listed product includes a made-to-order backplane PCB or engineering service.

Create a Series Passport

Information that must remain together

Manufacturer: identify the original connector manufacturer rather than relying on a reseller description.

Product family: record the named backplane system and any applicable subseries.

Series generation: distinguish revisions that may share a family name but use different mating geometry.

Backplane-side part: capture its connector type, orientation, module arrangement and PCB interface.

Daughtercard-side part: record the manufacturer-approved mating part or mating series.

Guide and coding: include guide modules, polarization and slot-specific coding in the same record.

Describe the Interconnect by Its Paths

High-speed signal path

Use the exact series datasheet to confirm pair organization, impedance, supported data rate, ground distribution and shielding. Do not transfer performance figures between unrelated connector families.

Power path

Identify power-contact locations, mating contact design, current rating and the temperature conditions under which that rating applies.

Hybrid path

Reproduce the specified arrangement of signal, power, ground, coaxial or other special modules without changing their location in the connector assembly.

Mechanical path

Check vertical, right-angle, coplanar or orthogonal geometry together with connector height, card insertion direction and enclosure clearance.

Test a Replacement Against the Existing System

  1. Compare both mating connector part numbers, not only the part being replaced.
  2. Overlay the PCB footprint, mounting holes, connector envelope and card-edge position.
  3. Match signal, power, ground and guide locations within the module arrangement.
  4. Confirm press-fit, solder or other termination requirements against the existing PCB.
  5. Check whether coding, guide, shield or retention components must also be changed.

Pitch, position count and external dimensions are screening fields only. Approve a replacement after the connector manufacturer confirms the mating interface, PCB pattern and series compatibility.

Read More
Custom Backplane ConnectorsResults:
Comprehensive
Price Priority
Stock Priority
Image
Part Number
Description
Availability
Unit Price(USD)
Quantity
Operation
Pre-order
1,600
Factory Lead Time:14-26 weeks
160+$36.2806
- +
Ext. Price(USD):$5,804.89
MOQ:160
Mult:16
SPQ:16
Available Stock
33
Estimated Ship Time:6-13 working days
1+$20.217
10+$15.3684
100+$13.7052
260+$12.9924
- +
Ext. Price(USD):$20.21
MOQ:1
Mult:1
SPQ:1
Hard Metric HDR Connector, 110 POS, 2mm Pitch, Press Fit, Thru-Hole
Available Stock
6
Estimated Ship Time:9-14 working days
1+$10.205
- +
Ext. Price(USD):$30.61
MOQ:3
Mult:1
SPQ:1
CONN PLUG 2POS PNL MNT
Available Stock
18
Estimated Ship Time:9-14 working days
1+$21.2004
20+$17.1569
260+$14.318
500+$13.6732
- +
Ext. Price(USD):$42.40
MOQ:2
Mult:1
SPQ:1
25 / PageGoto